Troubleshooting

Rosin Press Delivered the Inaccurate Temperature After Measuring with My Infrared (IR) Thermometer Gun, Why? To be honest, when we measure the temperature of the heating plate during the process of manufacturing, the temperature obtained by the infrared thermometer is different every time. Actually, many factors will affect the test results: 1. Measure different positions of the heating plate. 2. Measure under different ambient temperature. 3. Measure after modifying the parameters. 4. Measure by the different brands.5. Measure at different time points in the heating process. If possible, we recommend that you use a contact thermometer to measure the temperature or please verify the...

My Temp Controller Box Caused the Issue After Changing the Parameters, How to Fix It? First of all, we do not recommend changing the internal parameters, which will cause a lot of problems. Once a problem occurs after the modification, please refer to the following instructions to change back to the default.  How to Change back to the Default Setting of TC01V5?   #The following instruction is only applicable to "TC01V5" PID controller, not for "TC20V2". As of May 1st,2021, Only Dabpress 12 ton heat press uses  a PID temp controller with Item number "TC20V2".  # First of all, please refer to the...

How to Replace PID module? 1. Unplug the power cord from the rear of the temperature control box.2. Turn the temperature control box upside down to access the locking mechanism on the front of the PID module housing face.3. Use a dab tool or small flat head screwdriver to depress in on the locking mechanism at the front of the PID housing face.4. While depressing the locking mechanism, simply slide out the front of the box, the PID module from the housing (there will be 2 circuit boards exposed).5. Install the replacement PID module received (remove it from the included...

About 2x4" Rosin Pre Press Mold, Why Is the inside of the Mold Not 2x4"? This is one of the most asked questions by rosineer, we named this mold 2x4 just to declare that it pairs with 2x4 rosin filter bags. In order to reduce your confusion, we specifically mention the size of puck in the description. Now Let Us Talk about It in Details as Below; Usually we need to use the mold to form pucks. Please understand that the compressed puck which you put into the filter bags is a three-dimensional block, it has length,width, height. The filter bag just has...

How to Replace the Bottle Jack?The instruction is applicable to bottle jack styled heat press machine that need to replace the jack step by step: 1. Loose the bolts under the base and on the collar if includes.2. Ask someone to help you lift up the the heated plates.3. Remove the bottle jack. 4. After loading the replacement. If the replacement offers a thread, please pre-install the screws and nuts (do not tighted it)5. Lift the bottle jack till dual heated platens touched, and then adjust the dual heating plates to align with each other.6. Lift up the bottom heated plate harder, tighten all...

Piston Rod of Hydraulic Cylinder Rosin Press Can Lift But It Can Not Move Back, What happened? Caution: 1. Please ensure the pump has a NPT 1/4” male fitting;2. We recommend you to replace male fitting (From another brand) with ours for matching our press. There is improper operation caused this kind of issue, please check it out carefully: 1. Please make sure the male and female coupler installed completely. You need to push the male fitting into the female one fully, at the same time, please tighten the nut of the female coupler. Please try to reconnect couplers once you didn’t...

My Rosin Press Hydraulic Hand Pump Will Not Maintain Pressure Well, Why? To help prevent personal injury, always release pump pressure and disconnect hoses(s) from pump before making repairs.Refer to the appropriate pump parts list during trouble-shooting. Please check these problems yourself first, and then make clear what happened to your pump: Problem Cause Solution  Pump losing pressure System components leakingDirectional control valve leaks ornot adjusted properlyFluid leaking past outlet checkseat(s) Repair or replace as necessaryReseat, repair, or replace directional control assembly and correctly adjustCheck for dirt. Reseat pump body and/or replace poppet(s) or ball(s) Pump not delivering fluid Low fluid level...

Why Can't We Use Rosin Press to Produce the Puck of Flower or Hash? We at Ddabpress Team often receive complaints from Rosineers about why 2x4" rosin pre press mold can not load between the heated plates of the rosin press for making puck. Honestly, we can only patiently explain to customers that this kind of operation will scratch the contact surface and even damage the machine. The rosin press is used to extract plant essences oil, in the other words, it only gets used to squeezing some of the fine material. now let us explain in detail why such improper use...

My Bottle Jack Rosin Press Does Not Hold Pressure, Why?There are many factors that may cause the jack to not hold pressure, much apprecaited if you could check it out by yourself:  Symptom Possible Causes Corrective Action Jack will not lift load Release valve not tightly closedOverload conditionAir pressure inadequate Ensure release valve tightly closedRemedy overload conditionEnsure adequate air pressure Jack will lift, but not hold pressure Release valve not tightly closedOverload conditionHydraulic unit malfunction Ensure release valve tightly closedRemedy overload condition Jack will not lower after unloading Reservoir overfilled Ensure load is removed, then drain fluid to proper level...